I have a universal remote control, which I want to use with a TEAC micro hifi system. It needs programming to set the IR codes of the hifi.
The instructions say, press SET and the device name simultaneously, red light starts flashing, then press SET and then press POWER.
What I'm assuming this is doing, is outputting its different codes one by one, and each time you press POWER, hoping that one of the presses turns the hifi on or off. That shows its got the code, and then you check that volume up/down etc work on the remote.
I've now pressed the POWER button about 200 times and haven't found the code yet. DAK how many times I may have to do this?
Got a credit card? use our Credit Card & Finance Calculators
Thanks to bruncher,niord,gvonge,Shelford,GrahamPlatt, for Donating to support the site
how many presses?
-
- Lemon Slice
- Posts: 982
- Joined: November 4th, 2016, 10:31 am
- Has thanked: 338 times
- Been thanked: 457 times
Re: how many presses?
My admittedly limited experience suggests that with your universal remote control, you should (may?) have had a list of coded for various manufacturers. That might help.
Otherwise, it could be a lot - 3 digits = 1000 codes! And I believe some are 4 digit codes.
Good luck,
ten0rman
Otherwise, it could be a lot - 3 digits = 1000 codes! And I believe some are 4 digit codes.
Good luck,
ten0rman
-
- Lemon Half
- Posts: 5346
- Joined: November 4th, 2016, 12:04 pm
- Has thanked: 3320 times
- Been thanked: 1038 times
Re: how many presses?
The one thing I have come to understand about universal remote controls is that they are universally useless.
didds
didds
Re: how many presses?
It depends on what type of universal remote.
Some of them require a 3 or 4 digit code entered to tell it what device to control, and others are learning remotes, where you point the original remote at the learning remote and press the appropriate button.
Which universal remote is it?
Some of them require a 3 or 4 digit code entered to tell it what device to control, and others are learning remotes, where you point the original remote at the learning remote and press the appropriate button.
Which universal remote is it?
-
- Lemon Slice
- Posts: 982
- Joined: November 4th, 2016, 10:31 am
- Has thanked: 338 times
- Been thanked: 457 times
Re: how many presses?
Its has four modes - one where you can input a code if known, quick search mode, auto search mode (which is what I've previously described) and display mode (which is to show you the code it settled on.
Naturally, I'd prefer to input a code - DAK the code for a TEAC Micro hi-fi system DX40DAB please? Only TEAC code I found in my searches was 608, which doesn't work.
Naturally, I'd prefer to input a code - DAK the code for a TEAC Micro hi-fi system DX40DAB please? Only TEAC code I found in my searches was 608, which doesn't work.
-
- The full Lemon
- Posts: 19137
- Joined: November 4th, 2016, 3:58 pm
- Has thanked: 646 times
- Been thanked: 6793 times
Re: how many presses?
didds wrote:The one thing I have come to understand about universal remote controls is that they are universally useless.
Mine has worked great for 3 years. It should as it cost about five hundred quid. It's a MX-980. I love that it's rechargeable and that it is non-directional so you can operate it from the next room if you want.
BUT, if anything goes wrong with it I would have to call in the installer. Stuff has become way too complicated.
-
- 2 Lemon pips
- Posts: 119
- Joined: November 7th, 2016, 4:03 pm
- Has thanked: 11 times
- Been thanked: 36 times
Re: how many presses?
Are you supposed to hold the power button for as long as it takes to find the code? Might you be starting from the same place in the list of possibles every time you press for a short time?
Return to “Technology - Computers, TV, Phones etc.”
Who is online
Users browsing this forum: twigga and 12 guests